Name: China Blauberg BL-F160B-EC-02 160mm EC Forward Curved Centrifugal Fan Manufacturers Suppliers Factory - Blauberg
Brand: Blauberg Motoren
SKU: 315456842

Suzhou Blauberg Motoren Technology Co., Ltd. is one of the leading manufacturers and suppliers of blauberg bl-f160b-ec-02 160mm ec forward curved centrifugal fan in China. Welcome to buy bulk high quality customized products made in China here and get quotation from our factory. For price consultation, contact us.

Basic Info

Model	BL-F160B-EC-02	Product Type	EC Forward Curved Centrifugal Fan
Phase	1~	Rated Voltage	230 VAC
Frequency	50/60 Hz	Nominal Speed	1800 ±5% RPM
Max. Input Power	115 W	Max. Input Current	0.85 A
Sound Level	64 dB(A)	Ambient Temperature	-25 to +60 °C
Certification	CCC, RoHS	Protection	IP55

Technical Description

Dimensions	160 × 160 × 85.8 mm	Impeller Material	PA+GF
Rotation	Clockwise, viewed from rotor side	Rotor Surface	Powder coating
Insulation Class	Class B	Operating Mode	S1
Bearing	Ball bearing	Cable Length	500 ±20 mm
Humidity	5%–90% RH	Motor Type	External rotor EC motor
Impeller Deviation	Axial ≤0.5 mm; radial ≤0.5 mm	Motor Protection	Locked rotor, thermal, under/overvoltage and overcurrent

Product Application

1	Charging Column	9	Equipment Cooling Project
2	Kitchen Smoke Exhaust System	10	Ventilation Unit Project
3	FFU Project	11	AHU Project
4	Computer Room Cooling	12	Air Purifier Project
5	Rail Transit Air-Conditioning	13	Heat Exchanger Project
6	Electrical Appliances	14	Telecom Container Project
7	FanGrid Project	15	Data Center Cooling Project
8	Ventilation Equipment Project	16	Industrial Cooling System

Air Performance

BL-F160B-EC-02 Air Performance

Overall Dimensions

BL-F160B-EC-02 Overall Dimensions

Electrical Connection

BL-F160B-EC-02 Electrical Connection

Line	Conn.	Designation	Colour	Function / Assignment
Power Line		PE	Green/Yellow	Protective earth
Power Line	U1	L	Brown	Live wire
Power Line	U2	N	Blue	Neutral wire
Control Line	U4	+10V	Red	10 V control power output
Control Line	U5	Speed Control	Yellow	0–10 V/PWM speed-control input
Control Line	U6	Signal Feedback	White	RPM output signal
Control Line	U7	GND	Blue	Control ground

Note

1	Connect the power and control lines strictly according to the wiring diagram.
2	Do not connect the white signal wire directly to the red signal wire or an external DC supply.
3	If the fan does not start, check the speed-control input voltage and wiring.
4	The fan may take several seconds to start; do not touch the impeller or rotor while energized or running at low speed.
5	Before power-on, verify that the motor is installed securely.
6	Do not pull the power cable; a damaged cable must be replaced by the manufacturer.
7	Do not drop or strike the motor.
8	Do not flush the motor with water.
9	Consult Blauberg before using a customized product outside the agreed operating conditions.
10	The motor casing may remain hot after shutdown; take precautions against burns.
11	Keep debris out of the casing and clean the interior when necessary.
12	Before installation and operation, rotate the rotor by hand to confirm there is no collision, interference or jamming.
13	Do not use the motor alone without the impeller or load.
14	Store the repacked product at -40 °C to +80 °C and no more than 95% RH, free of corrosive gases and at least 15 cm above the floor.
15	Install the fan out of children's reach and do not allow children to use it.
16	The final interpretation right of this specification belongs to Blauberg.

Life and Maintenance, Warranty

1	The design life is 50,000 hours at 40 °C, limited by ball-bearing life; actual service life varies with temperature, humidity, installation, load and other operating conditions.
2	Clean and maintain the fan every 3–6 months according to the operating environment.
3	The whole-machine warranty is two years from purchase (subject to delivery date). Manufacturing-quality failures are repaired or replaced free of charge; damage caused by improper disassembly, handling, misuse, natural disaster or force majeure is excluded.